A) Term Work Assessment Scheme
The
term work of concerned subjects shall be assessed on the basis of Tutorials (if
applicable),
assignments, class tests and practical performance of the student.
B) Guidelines for Nature of
Question Paper for T.E (Electronics) Part-I & II.
1. There shall be total six questions in each paper, all being
compulsory with internal options.
2. Each question paper shall consists of two sections(Section I
& Section II).
3. Duration of each paper shall be of Three Hours Carrying of
Maximum 100 Marks.
C) Industrial Visits in T.E
(Electronics) Part-II are Compulsory.
T.E. (Electronics
Engineering) Semester -V
Microprocessor
Peripherals and Interfacing
Teaching Scheme Examination Scheme
Theory
: 4 Hours/Week Theory : 100 Marks
Practical
: 2 Hours/Week Term work : 25 Marks
POE
: 50 Marks
SECTION – I
Unit – I: Memory and decoding
logic: (6 Hrs)
Review
of flip flop, 74LS373 latch, concept of tri-state buffer, 74LS244, 74LS 245,
74LS138,
Concept
of memory, Types of memory, Memory organization, Memory expansion with
appropriate
decoding
logic.
Unit – II: Fundamentals of
Microprocessor: (12 Hrs)
8085
architecture, programming model: Addressing modes, Instruction set, Assembly
language
programming,
pin functions, Timing diagram and instruction cycles, State transition diagram,
Single
machine
cycle execution, stack and subroutines, Interrupt structure and classification.
Unit – III: I/O Interfacing
Techniques: (6 Hrs)
Concept
of I/O port, I/O mapped I/O, Memory mapped I/O Polling and interrupt driven
I/O, 8255 PPI:
mode
0, Mode 1, Mode 2.
SECTION – II
Unit – IV: Parallel I/O
Interfacing using 8255: . (8 Hrs)
Keyboard
and display interface (Static and Dynamic), Multiplexed thumbwheel switch
interfacing,
steeper
motor Interfacing, Centronic type printer interfacing, ADC (0809) & DAC
(0808) interfacing.
Unit – V: Study of 8279 and 8253:
(8 Hrs)
Basic
block Diagram, Various operating modes, interfacing with 8085
Unit – VI: Study of 8259 and 8251:
(8 Hrs)
Basic
block Diagram, Various operating modes, Interfacing with 8085
Text Books:-
1.
Douglas V.Hall, “Microprocessors and Digital Systems”, 2nd Edition , Tata Mc-Graw Hill.
2.
Ramesh Gaonkar, “Microprocessor Architecture Programming and Application with
8085”,
5th Edition, Penram International
Publishing India.
3.
K. Udaya Kumar, B.S. Umashankar, “The 8085 Microprocessor Architecture,
Programming
and
Interfacing”, Pearson
Reference:-
1.
Intel data sheet
2.
S. P. Chowdhary, Sunetra Chowdhary, “Microprocessor and Peripherals”, Scitech
Pub.
3.
Keneeth Short, “Microprocessor Logic”
LIST OF EXPERIMENTS
Minimum 12 Experiments to be
conducted
Note: Use of Assembler directives
& cross compiler is essential
Software Experiments:- Minimum 4 Experiments to be conducted.
1. Experiment Based on Arrays:-
(Minimum one)
Exchange,
Addition, Finding Minimum / Maximum, Ascending / Descending, Reverse,
Average,
etc.
2. Experiment Based on Arithmetic
and Logical Operation:- (Minimum one)
Multidigit
Addition, Multiplication / Division, Finding Even / Odd Numbers, Factorial,
Fibonacci
Series.
3. Experiment Based on Code
Conversion:- (Minimum one)
Binary
to BCD, BCD to Binary,
Binary
to Gray, Gray to Binary, etc.
4. Experiment Based on above with
use of subroutines from monitor
Program:- (Minimum one)
a)
Simulation of up / down counter changing mode with key press.
b)
Finding and displaying the factorial for key Entry from keyboard.
c)
Addition of two numbers entered from keyboard & display the result.
d)
Generation of different frequency square wave on SOD pin using key stroke.
e)
Study of interrupts.
Hardware Experiments:- Minimum 8 Experiments to be conducted.
8255 Based Experiments: (Minimum
Three)
1.
Multiplexed Display interface using 8255.
2.
Multiplexed Thumbwheel Switch interface using 8255.
3.
Simulation of Boolean Expression on 8255 ports.
4.
Simulation of multiplexer / De-multiplexer.
5.
Simulation of presetable up-down counter on 8255 port only.
6.
Stepper motor interface.
7.
ADC interface.
8.
DAC interface.
9.
Centronics Printer interface mode-I (8255).
8279 Based Experiments: (Minimum
Two)
1.
Encoded scan keyboard display mode
2.
Decoded scan keyboard display mode
3.
Multiplexed Thumbwheel Switch using sensor matrix mode
4.
Dynamic (rotating) display
5.
Flashing of message
8253 Based Experiments: (Minimum
one)
1.
Real time clock
2.
Frequency Counter
3.
Duty cycle control using 8253 (Application such as DC motor speed control or
lamp intensity
control)
8251 Based Experiments: (Minimum
one)
1.
Synchronous Transmitter / Receiver
2.
Asynchronous Transmitter / Receiver
8259 Based Experiments: (Minimum
one)
1.
Fully nested structure with single / master slave
2.
Rotating Priority Structure
3.
Special Mask Mode
4.
Special Fully Nested Mode (SFNM)
Guidelines for Paper Setter :
Theory
Question Paper should include 25 to 40% Programming Problems.
T.E. (Electronics
Engineering)
Semester -V
Analog Integrated
Circuits & Applications
Teaching Scheme Examination Scheme
Teaching
: 4 Hours/Week Theory : 100 Marks
Practical
: 2 Hours/Week Term work : 25 Marks
POE
: 50 Marks
SECTION – I
Unit – I: Differential Amplifiers
(5 Hrs.)
Differential
Amplifier- Configuration, DC & AC Analysis of Dual Input Balanced Output
Configuration.
Comparative study of other configuration of Differential amplifiers, Constant
Current
Bias,
Current Mirror, DC coupling & Cascade differential stages, Level Translator
& its need.
(Numericals
are expected).
Unit- II: OP-Amp Characteristics
(6 Hrs.)
Block
Diagram of Op-Amp, Ideal & Practical Op-amp specifications, Transfer
characteristics of Opamp,
Op-amp
parameters & measurement: Input & output offset voltages, Input &
output offset
currents,
Input Bias current, slew rate, CMRR, PSRR, Thermal drift. Comparative study of
Data
Sheets
– μA 741, OP 07, LM 324, LM 311, LM 308, LM380, CA 3140.
Unit- III: Op-Amps Configuration (8
Hrs.)
Open
Loop & Closed Loop- Inverting, Non-Inverting and Differential (Using one
op-amp). Analysis
for
Av, Ri, Ro, Bandwidth, and Total output offset voltage. AC & DC amplifiers
– all configurations. (Numericals are expected).
Unit- IV: Frequency Response &
Compensation Techniques (5 Hrs.)
Open
loop frequency Response, Closed loop frequency response, circuit stability,
slew rate. Input
offset
voltage and Input offset current compensation networks. Frequency compensation-
Lead-Lag
compensation.
Pole- Zero compensation.
SECTION – II
Unit- V: Linear Applications (5
Hrs.)
Summing
amplifier (Inverting & Non-Inverting), Sub tractor, Integrator,
Differentiator,
Instrumentation
Amplifier (3 op-amps), Instrumentation amplifier using transducer bridge, I-V
& V-I
converter.
(Numericals are expected).
Unit- VI: Non-Linear Applications
(5 Hrs.)
Comparators,
Zero Crossing Detector, Window detector, Schmitt trigger, peak detector, log
and antilog
amplifier,
precision rectifier, sample and hold circuit.
Unit- VII: Active Filters (6 Hrs.)
First
& Second Order Butterworth Low Pass, High Pass, Band Pass, Band Reject,
& All Pass Filters,
State
Variable, Bi-Quad, KRC-Filters (Analysis & Numericals are Expected).
Unit- VIII: Monolithic IC
Applications (8 Hrs.)
Sine
wave generator- RC phase Shift, Weins Bridge,& Quadrature oscillator.
Square wave (Astable
Multivibrator),
Monostable Multivibrator, & Triangular Wave generator, V-F, F-V converter
using opamp.
IC
555 (Timer): Block Diagram, Multivibrators and Applications. IC 566 VCO, PLL-
Introduction,
Block
Diagram, Principles & description of individual blocks, IC 565 PLL &
Applications. IC 8038
Waveform
generator (Numericals are expected).
Text Books:
1.
Ramakant. A.Gayakwad, “Op-Amps & Linear Integrated Circuits”, 3rd Edition, PHI.
2.
S.Salivahanan & Bhaaskaran, “Linear Integrated Circuits”, 1st Edition, Tata McGraw Hill.
Reference Books:
1.
National Analog & Interface products Data book—National Semiconductors
2.
T.R Ganesh Babu, “Linear Integrated Circuits”, 3rd
Edition, Scitech Publication.
3.
Sergio Franco, “Design with op-amp & Analog Integrated Circuits”, 3rd Edition, Tata McGraw
Hill.
4.
David. A. John & Ken Martin, “Analog Integrated Circuit Design”, Student
Edition, Wiley.
5.
Rashid, “Microelectronics Circuits Analysis & Design”, 1st Edition, Cengage Learning.
6.
J. Michael. Jacob, “Application & Design with Analog Integrated Circuits”,
2nd Edition,
PHI.
7.
Roy Choudhury & Shail. B. Jain, “Linear Integrated Circuits”, 2nd Edition, New Age
Publishers.
List of Experiments
Minimum 12 Experiments:
1.
Study of Data sheets of following IC’s ( Compulsory)
μA
741, OP 07, LM324, LM 308, LM380, CA 3140, LM 311.
2.
Measurement of op-amp parameters Using IC 741
a)
Input offset voltage b) Input offset current c) slew rate d) CMRR.
3.
Study of Inverting amplifier for DC & AC inputs using IC 741
4.
Study of Non-Inverting amplifier for DC & AC inputs using IC 741
5.
Frequency Response of Inverting & Non-Inverting amplifier using IC 741
6.
Study of op-amp as Summing, Scaling, & Averaging amplifier in Inverting
& Non-Inverting
Configuration
using IC LM 308
7.
Study of Instrumentation Amplifier using LM 324
8.
Study of V-I & I-V Converter using IC 741
9.
Study of Schmitt Trigger using IC 741 & Window detector using LM 311
10.
Study of Comparator & ZCD using LM324/OP 07
11.
Study of Precision Rectifier using IC 741
12.
Study of Butterworth Filter ( Any Two) using IC 741
13.
Study of Triangular & square wave generator using IC 741
14.
Study of IC 555 Timer as Astable & Monostable Multivibrator( NE/SE 555)
15.
Study of IC NE 565 PLL
16.
Study of V-F converter using LM311
17.
Study of Weins Bridge Oscillator using IC 741
18.
Study of Function Generator using IC 8038.
T.E. (Electronics
Engineering)
Semester –V
Digital System Design
Teaching Scheme Examination Scheme
Lectures
: 4 Hours/Week Theory : 100 Marks
Practical
: 2 Hours/Week Term work : 25 Marks
POE : 50 Marks
SECTION – I
Unit 1: Introduction to VHDL (5
hrs.)
Levels
of abstraction, Need of HDL , VLSI Design flow,
Features and capabilities of VHDL,
Elements
of VHDL (Entity, Architecture, Library, Package, configuration ),Identifiers
,literals , data types, operators.
Unit 2 : Combinational logic
design using VHDL (6hrs)
Adder,
subtractor, decoder, encoder, tristate buffer, multiplexer, parity generator,
parity checker,
comparator,
using Concurrent & Sequential statements.
Unit 3: FSM Design Using VHDL (9
hrs)
Impediments
to synchronous design, clock jitter, skew, gating the clock, asynchronous
inputs,
meta-stability
and synchronizer failure. VHDL implementation of counter, shift register, LFSR,
Serial adder. Bus arbiter, Single port RAM, Dual port RAM, FIFO,
SECTION – II
Unit 4: VHDL Features (6hrs)
Attributes
(type, signal, signal value, array, block) , wait statement, Simulators, Event
based simulator, Cycle based Simulator, Flow chart for Event scheduling and
delays , Inertial delay, Transport delay.
Unit 5: Processor Design (7hrs)
Design
of General purposes processor having instructions like LOAD, STORE, ADD, SUB,
IN, JZ, JPOS, HALT. Design of Data path, Design of control unit, test bench
using text IO.
Unit 6: PLD Architectures and
Testing (7hrs)
Xillnx
9500 series CPLD ( XC9572), Spartan II FPGA (XCS 2s30)
Testing:
Fault models, path sensitizing, random test, design for testability, Built-in
self test and
Boundary
scan.
Text books:
1.
Enoch O. Hwang “Digital logic and microprocessor design with VHDL”, Thomson
Publication
2.
Roth John “Principals of Digital System Design using VHDL”, 2nd Edition, Cengage Learning
Reference Books :
1.
K. C. Chang “Digital Systems Design with VHDL and Synthesis An Integrated
Approach”, 1st
Wiley-
India.
2.
Stephen Brown and Zvonko Vranesic “Fundamentals of Digital Logic with VHDL
design”,
Tata-
McGraw Hill
3.
Xilinx data manual “ The Programmable Logic data Book”
4.
S. S. Limaye “VHDL a Design Oriented approach” , Mc-Graw Hill .
Practicals:
Experiments: Minimum 10 experiments based on following designs. Each
design must
be
tested through VHDL test bench.
Simulation, Synthesis, and
Implementation using FPGA and CPLD Trainers:
1.
Combinational Logic: Decoder, priority encoder, comparator, adder, barrel
shifter.
2.
Sequential logic: Counters with synchronous/ asynchronous reset signal,
universal shift registers, sequence detector, Arbiter, LFSR.
3.
Single port RAM, Dual port RAM, FIFO.
4.
General purpose processor.
Lab Requirement:
Model
Technology, Modelsim simulator and Xilinx Web pack.
VLSI
universal trainer for FPGA and CPLD of Xilinx.
Guidelines for Paper Setter:
Theory
Question Paper should include 25 to 40% Programming Problems.
T.E. (Electronics
Engineering)
Semester –V
Electromagnetic
Engineering
Teaching Scheme Examination Scheme
Lectures
: 3 Hours/Week Theory : 100 Marks
Tutorial : 1 Hour/Week Term work : 25 Marks
SECTION– I
UNIT-I: Electrostatics (8 Hrs.)
Review
of vector Analysis and coordinate systems, Coulomb’s law & electric field,
field due to
distributed
charges, Flux density, Gauss’s law and its applications, divergence theorem,
Electrostatic
potential,
potential gradient, electric dipole, Electrostatic energy density, Boundary
conditions for
electrostatic
field.
UNIT-II: Steady Magnetic Field (7 Hrs.)
Biot
Savarts law, Ampere’s circuital law, Stoke’s Theorem, Magnetic flux density
& Vector magnetic
potential,
Current carrying conductors in magnetic fields, Torque on loop, Energy stored
in magnetic
field,
Boundary conditions for magneto static field.
UNIT-III: Maxwell’s Equations (3
Hrs.)
Inconsistency
of Ampere’s law, Faraday’s law, Maxwell’s equations for static field, time
varying
field
& harmonically varying fields, Comparison of field & circuit theory.
SECTION – II
UNIT-IV: Electromagnetic Waves (7
Hrs.)
Wave
propagation in dielectric & conducting media, Modification in wave
equations for sinusoidal
time
variations, Characteristics of plane wave in a) pure dielectric media, b)
Conducting media,
Reflection
of electromagnetic wave for normal incidence, Polarization.
UNIT-V: Poynting Theorem (3 Hrs.)
Poynting
theorem, Power flow in uniform plane wave, Circuit applications of the Poynting
vector.
UNIT-VI: Transmission Lines (8
Hrs.)
Transmission
line equations, Transmission line parameters, Infinite line, terminated uniform
transmission
line, Reflection coefficient, VSWR, group velocity, phase velocity,
Applications of
Smith
chart for Impedance matching Technique a) Single stub b) Double stub.
Term Work: Minimum 8 Tutorials based on the above units.
Text Books:
1.
John D. Kraus, “Electromagnetics”, Mc Graw Hill.
2.
William Hayt, Buck, “Engineering Electromagnetics”, Mc Graw Hill.
3.
G.S.N. Raju, “Electromagnetic field theory & Transmission lines”, 1st edition, Pearson Education.
4.
Nanna Paneni Narayana Rao, “Elements of Engineering Electromagnetics”, 6th edition, Pearson
Education.
Reference Books:
1.
Jordan & Balmain, “Electromagnetic Fields & Radiation Systems”, 2nd edition, PHI.
2.
David K Cheng, “Field & Wave Electromagnetics”, 2nd edition, Pearson Education.
3.
Sadiku, “Elements of Electromagnetics” 4th
edition, Oxford University Press.
4.
R K Shevgaonkar, “Electromagnetic Waves”, 1st
Edition, Tata McGraw Hill.
Guidelines for Paper Setter:
Theory
Question Paper should include 40% Theory & 60% Numerical Problems.
T.E. (Electronics
Engineering)
Semester -V
Control Systems Engineering
Teaching Scheme Examination Scheme
Lectures
: 3 Hours/Week Theory : 100 Marks
Practical : 2 Hours/Week Term work : 25 Marks
SECTION – I
UNIT-I: Introduction to Feedback
Control System (7 Hrs.)
Classification
of control System, Mathematical models of physical system- Electrical &
Mechanical System , Transfer function, Deriving transfer function of physical
system - field controlled and armature controlled DC servo motors, Block
diagrams and reduction techniques including signal flow graphs.
UNIT-II: Feedback characteristics
of Control system (4 Hrs.)
Feed
back & Non-feedback systems, Reduction of parameter variations by use of
feedback, control over system dynamics by use of feedback, control of effect of
disturbance signals by use of feedback, linearizing effect of feedback,
Regenerative feedback.
UNIT-III: Time Domain Analysis (7
Hrs.)
Time
response of first order & second order system using standard test signal,
steady state errors and error constants, Root locus techniques- Basic concept,
rules of root locus, application of root locus techniques for control system.
SECTION – II
UNIT-IV: Frequency Domain Analysis
(9 Hrs.)
Introduction,
correlation between time & frequency domain, Bode plots, gain margin, phase
margin, effect of addition of poles & zeros on bode plots, Polar plots,
Nyquist stability.
UNIT-V: Analysis of control system
in state space (4 Hrs.)
Basic
concepts of state, state variable & state models, controllability,
observability, Derivation of
Transfer
Function from state model for continuous time system.
UNIT-VI: Compensators &
controllers (5 Hrs.)
a.
Compensators- Need of compensation, lead compensation, lag compensation,
Lead-lag
compensation.
b.
Controllers- Introduction, Proportional, Integral, derivative & PID
controllers.
Introduction
to PLC controllers.
Text Books:
1.
I.J. Nagrath, M.Gopal “Control Systems Engineering”, 5th Edition, New Age International
Publication
2.
Schaum’s Series book “Feed back Control Systems”.
3.
Les Fenical “Control Systems”, 1st Edition, Cengage Learning India.
4.
R. Anandanatarajan, P. Ramesh Babu , “Control Systems Engineering”, Scitech
Publications
Reference Books:
1.
Norman S. Nise “Control Systems Engineering”, 4th
edition, Wiley edition.
2.
Samarjeet Ghosh, “Control Systems Theory & Applications”, 1st edition,
Pearson education.
3.
S.K. Bhattacharya, “Control Systems Engineering”, 1st edition, Pearson
education.
4.
Hackworth, “Programmable Logic Controller”, 1st edition, Pearson education.
Practical List:
1.
Determination of transfer functions of physical system.
2.
Transient response of second order system for a step input.
3.
Verification of Bode plot using Lead Network.
4.
Verification of Bode plot using Lag Network.
5.
Frequency response of control system.
6.
Response of PID controller.
7.
Study of PLC.
Software based experiments using
MATLAB.
1.
Transient response of second order system by using standard test signals.
2.
Draw a root locus of any system.
3.
Draw a Bode Plot.
4.
Draw a Polar Plot.
5.
Draw a Nyquist Plot.
6.
Obtain a transfer function from state space model.
7.
Check the controllability and observability of system.
Note: Any five experiments from
Hardware based practical & all software based practical.
Guidelines for Paper Setter :
Theory
Question Paper should include 50% Numerical Problems.
T.E. (Electronics
Engineering)
Semester -V
MATLAB
Programming
Teaching Scheme Examination Scheme
Lectures
: 2 Hours/Week
Practical : 2 Hours/Week Term work : 25 Marks
SECTION – I
UNIT- I (5 Hrs.)
Matlab
basics variables, arrays , Multidimensional subarrays , Special values,
displaying output data,
data
files, scalar and array operations, Hierarchy of operations built-in matlab
functions, introduction
to
plotting, Debugging matlab programs.
UNIT- II (4 Hrs.)
Branching,
Statements and logical data type, Branches, write & for loop logical arrays
and
vectorization.
UNIT- III (5 Hrs.)
User-defined
& I/O functions, introduction to matlab functions, Variable passing in
matlab, Three
optional
arguments, Sharing data using global memory, Preserving data between calls to a
function,
function
functions, subfunctions, Private functions, Nested functions, complex data ,
string functions ,
textread
function, load and save commands, an introduction to matlab file processing,
file opening and
closing
, binary I/O functions, formatted I/O functions, comparing formatted and binary
I/O function,
file
positioning and status functions.
UNIT- IV (3 Hrs.)
Handle
graphics & gui , the matlab graphics system, Object handles, examining and
changing object
properties,
Using set to list possible property values, user-defined data, finding objects,
selecting
objects
with the mouse, creating and displaying a graphical user interface, object
properties, graphical
user
interface components, dialog boxes, menus.
UNIT- V (3 Hrs.)
Simulink
basics: introduction, simulink, modeling, solvers, simulating model using
variables from
matlab,
data import/export , state –space modeling & simulation, creation of
subsystems, & Mass
subsystem.
Text Books:
1)
Stephen J. Chapman “MATLAB programming for engineers”, 3rd Edition, Cengage
Learning
2)
Rajkumar Bansal, Ashokkumar Good, Manojkumar Sharma, “MATLAB & its
application in
engineering”,
1st Edition, Person Education.
3)
Amos Gilant “MATLAB & Introduction with application”, Wiley India.
Reference Books:
1)
Duane Hansel man, Bruce Littlefiele “Master in MATLAB-7” Person Education.
2)
MATLAB programming manual by Mathworks Inc.
3)
Partha S.Mallick “MATLAB & simulink – Introduction to applications”,
Scitech publications.
List of MATLAB programs
1)
Program using branching statement
2)
Program using looping statement
3)
Program for matrix manipulation
4)
Program using user defined function
5)
Program for handling complex data
6)
Program for File handling & string manipulation (Any two)
7)
Program for creating & Displaying GUI (Any two)
8)
Mini project based on any Engineering applications.( It should be completed
within Two or
Three
Practical Turns)
T.E. (Electronics
Engineering)
Semester -VI
MICROCONTROLLERS
Teaching Scheme Examination Scheme
Lectures
: 4 Hours/Week Theory : 100 Marks
Tutorial
: 2 Hours/Week Term work : 25 Marks
POE : 50 Marks
SECTION-I
UNIT-I: 8 Bit Microcontrollers
(6Hrs.)
Introduction
to Microcontrollers, 8051 architecture, functional pin description , memory
organization,
SFRS
& ON-CHIP resources of 8051, External program & data memory interface,
comparative study between different family members
(80s52,89c51RD2,89c420,ADuC812).
UNIT-II: Programming 8051 (8 Hrs.)
Addressing
modes, instruction set, Assembly language programming.
UNIT-III: On-chip Resource
Programming & Interfacing (8 Hrs.)
Interrupt
structure, port structure & operation, Timer/Counters (internal structure
& various modes),
serial
port & it’s modes (hardware details of mode-1 only)
Interfacing
keypad, seven-segment display, ADC, DAC, LCD interfacing.
SECTION-II
UNIT-IV: Introduction to PIC
Microcontrollers (6 Hrs.)
Introduction
to RISC and CISC Architectures, Introduction to Microchip PIC family
PIC
16F877 architecture, RESET, memory organization, Register file structure, CPU
registers.
UNIT V: PIC Programming (4 Hrs.)
Instruction
set, Assembly language programming.
UNIT VI: On chip Resources and
Programming (12 Hrs.)
Overview
of: I/O ports, Timers, CCP module, Comparator, ADC, Interrupt structure, WDT,
Sleep
timer,
SSP.
Text Books:
1)
Mazidi, “8051 microcontroller and embedded systems using assembly and C”, 2nd edition,
Pearson
education.
2)
Ajay Deshmukh, “Microcontrollers theory and applications”, Tata McGraw Hill
Reference Books:
1)
Kenneth Ayala, “The 8051 Microcontroller”, Cengage Learning.
2)
PIC microchip mid range MCU family reference manual
3)
I. Scott Mackenzie, Raphael C, “The 8051 microcontroller”, 4th edition, Pearson education.
4)
J.B. Peatman, “Design with PIC microcontrollers”, Pearson education.
5)
Intel Handbook on 8 bit & 16 bit embedded controllers –Intel
Practicals:
Minimum
Ten Experiments (Five each -from section I, and section II)
NOTE: Use of Assemblers, Simulator and development boards for MCS51
and PIC is recommended.
Guidelines for Paper Setter:
Theory
Question Paper should include 25% programming problems based on above syllabus.
T.E. (Electronics
Engineering)
Semester -VI
DIGITAL COMMUNICATION
Teaching Scheme Examination Scheme
Theory
: 4 Hours/Week Theory : 100 Marks
Practical : 2 Hours/Week Term work : 25 Marks
SECTION – I
Unit – I: Random Variables Theory
& Processes (9 Hrs.)
Probability,
Properties of Probability, Joint & Conditional Probability. Random
Variables: Cumulative Distribution Function(CDF), Probability Mass Function,
Probability Density Function(PDF), Joint CDF & joint PDF, Statistical
Averages, uniform distribution, Rayleigh distribution & Gaussian PDF. Random
Process, Time averaging & Ergodicity, Auto correlation, Power spectral
density of stationary random process. Noise in communication system, white
noise..
UNIT-II: Source Coding (8 Hrs.)
Quantization-
Uniform Quantization, Non uniform Quantization, Companding, Pulse Code
Modulation
(PCM), Effect of noise, Bandwidth, Differential Pulse code modulation (DPCM),
Delta modulation, Noise in delta modulation, Adaptive delta modulation(ADM),
CVSD. Performance of all coding schemes based on SNR.
Unit-III: Digital Signaling
Formats (5 Hrs.)
Introduction,
Non Return to zero(NRZ) codes, Return to Zero, Phase Encoding, M-array format,
Synchronization-
Bit or Symbol Synchronization, Frame Synchronization, Carrier recovery
circuits, scramblers & unscramblers.
SECTION – II
UNIT –IV: Digital Modulation
Techniques (10 Hrs.)
Amplitude
Shift Keying (ASK), Phase Shift Keying (PSK), Frequency Shift Keying (FSK),
Coherent & Non-coherent detection, Binary Phase Shift Keying (BPSK),
Quadrature Phase Shift Keying (QPSK) , Differential Phase Shift Keying (DPSK),
Differentially Encoded Phase Shift Keying (DEPSK), Minimum Shift Keying (MSK),
Gaussian Minimum Shift Keying (GMSK), Quadrature Amplitude Modulator (QAM).
Bandwidth, Signal Space representation, Probability of bit error of all Schemes.
UNIT –V: Baseband Transmission
& Optimum Detection ( 6 Hrs.)
Baseband
transmission of binary data, Inter symbol Interference (ISI) & its
minimization, NYQUIST Pulse Shaping Criterion, Pulse Shaping by Digital
Methods, Eye Pattern, M-ary signaling, Correlative coding- Duo-binary
signaling. Optimum Receiver-Matched Filter& its Properties, Correlation
receiver, Adaptive equalization & Schemes.
UNIT – VI: SPREAD SPECTRUM
MODULATION (6 Hrs.)
Introduction,
Direct Sequence (DS) Spread Spectrum, Use of Spread Spectrum with Code Division
Multiple
Access(CDMA), Ranging Using DS Spread Spectrum, Frequency Hopping (FH) Spread
Spectrum,
Generation & Characteristics of PN Sequences
Text Books:
1)
Simon Haykin “Digital Communication” Wiley India Edition
2)
Taub & Schiling “Principles of communication System”IInd Edition, Tata
McGRAW Hill
3)
Bernard Sklar “Digital Communication-Fundamentals and Applications” IInd
Edition ,
Pearson
Education
Reference Books:
1)
B.P. Lathi “Modern Digital & Analog Communication System”
2)
Singh & Sapre “Communication Systems”
3)
Glover & Grant “Digital Communication” IInd Edition, Pearson Education
4)
John Prokis ”Digital Communication” Pearson Education.
5)
K.Sam Shanmugan “Digital & Analog Communication Systems” Wiley India
Edition
6)
M.S. Roden “Analog & Digital Communication Systems”, 5th Edition, Shroff Publications.
Practicals:
Minimum
Ten Experiments should be performed.
EXPERIMENT LIST:
1)
Study of Pulse Code Modulation
2)
Study of Delta Modulation
3)
Study of Adaptive Delta Modulation
4)
Study of Data format
5)
Study of Amplitude Shift Keying
6)
Study of Frequency Shift Keying
7)
Study of Phase Shift Keying
8)
Study of Quadrature Phase Shift Keying
9)
Study of any modulation technique using MATLAB
10)
MATLAB practicals on Random signals
11)
Study of Standard Random Variables Density Distribution Function
Guidelines for Paper Setter:
Theory
Question Paper should include 15% Numericals and 85% Theory.
T.E. (Electronics
Engineering)
Semester -VI
Power Electronics
Teaching Scheme Examination Scheme
Lectures
: 4 Hours/Week Theory : 100 Marks
Practicals
: 2 Hours/Week Term work : 25 Marks
POE : 50 Marks
SECTION – I
UNIT-I: Silicon Controlled
Rectifier (9 Hrs.)
Construction-
: V-I Characteristics, Dynamic Characteristics during turn on,
turn off, gate triggering Characteristics, Rating & specifications, SCR
triggering methods- R, RC,UJT triggering (using pulse transformer), PUT,SUS,SBS
triggering methods. SCR Turn off method, Class A, Class B, Class C, Class D,
Class E, & Class F, dv/dt & di/dt protection circuits. Heat sink
design.
UNIT-II: Power Devices &
Driving Circuits (6 Hrs.)
Construction,
working, V-I Characteristics, Driving Circuit of :Diac, Triac, GTO, MOSFET,
IGBT.
UNIT-III: 1 Φ Controlled Converter
(9 Hrs.)
1
Φ Half Wave Controlled Rectifier, 1 Φ Full Wave Controlled Rectifier, Midpoint
configuration & bridge configuration with R,RL & Battery with &
without Free wheeling Diode, 1 Φ semi converter, Full Converter & dual
converter. (Derivations & Numericals expected).
SECTION – II
UNIT-IV: Chopper Circuits (9 Hrs.)
Introduction
to Choppers, classification, control techniques of choppers, series turn off
chopper,
parallel
Capacitor Turn off chopper, Jones & Morgan’s Chopper; step up chopper,
Multi Phase
chopper
(Circuits based on SCR & IGBT).
UNIT-V: A.C. Voltage Regulator (6
Hrs.)
Switch
mode AC power supplies, Resonant AC power supply, Bidirectional AC power
supply,
Control
circuits of SMPS. AC voltage Stabilizer- Relay type, Servo type, Constant
Voltage
Transformer.
UNIT-VI: Power circuits &
Systems (9 Hrs.)
AC
power flasher using Triac, light dimmer using Triac and Diac, Liquid level
controller, 1 Φ
preventer,
burglar Alarm, Product counter, SCR driving circuit using optocoupler, battery
charger, proximity detector circuit.
Note: Industrial Visit is compulsory & Visit report is expected.
Text Books:
1.
P.C. Sen, “Power Electronics”, 1st Edition, Tata McGraw Hill.
2.
M.H. Rashid, “Power Electronics”, 3rd
Edition, Pearson.
3.
G.E. SCR Manual.
Reference Books:
1.
Mohan, Undeland, Riobbins, “Power Electronics” 3rd
Edition, Wiley.
2.
Dubey, Doralda, Joshi,Sinha, “Thyristorised Power Controllers”, 1st Edition, New Age
International
Edition.
3.
M.D. Singh, K.B. Khanchandani, “Power Electronics”, 2nd Edition, Tata- McGraw Hill.
Practical List:
1.
VI Characteristics of SCR.
2.
SCR as Half wave controlled rectifier.
3.
Triac as light dimmer.
4.
A.C. Power Flasher.
5.
SCR Triggering Circuits.
6.
SCR Commutation Circuits.
7.
Liquid level controller.
8.
Single phase preventer.
9.
AC voltage regulator.
10.
SCR step down chopper.
11.
Single phase semi- converter.
12.
Single phase Full- converter.
13.
Burglar Alarm.
14.
Batch counter.
Guidelines for Paper Setter:
Theory
Question Paper should include 15% Numericals and 85% Theory.
T.E. (Electronics
Engineering)
Semester -VI
Digital Signal
Processing
Teaching Scheme Examination Scheme
Lectures
: 4 Hours/Week Theory : 100 Marks
Practical : 2 Hours/Week Term work : 25 Marks
SECTION – I
UNIT-I: The Discrete Fourier
Transform and FFT (10 Hrs.)
Introduction
to DSP system, DFT, Relation between DFT and Z –Transform, Properties of DFT,
Circular
convolution- DFT & IDFT. FFT algorithms (DIT FFT & DIF FFT)
implementation aspects, fast convolution signal, segmentation (overlap save
& overlap-add algorithm), correlation – circular correlation, IFFT, DFT
properties of circular correlation.
UNIT-II: FIR Filter Design (5
Hrs.)
Characteristics
of FIR filter, properties of FIR filter, digital N/W for FIR filter, frequency
sampling, Fourier series & windowing method, filter design using Kaiser
window, Realization of FIR by direct form structures, cascade, parallel form.
UNIT-III: IIR Filter Design (6
Hrs.)
Impulse
invariant technique, Bilinear transformation, Placement of poles & zeros,
frequency band
transformation,
analog filter approximation (Butterworth) quantization and rounding problems,
Effect of finite word length on stability and frequency response, Realization
of IIR by direct form structures,cascade & parallel form.
SECTION – II
UNIT-IV: Adaptive filter (6 Hrs.)
Introduction
to adaptive signal processing, Adaptive direct form FIR filters- Least Mean
Square
(LMS)
algorithm.
UNIT-V: DCT & Wavelet
Transform (10 Hrs.)
Forward
DCT, Inverse DCT, DCT as a orthogonal transformer.
Introduction
to wavelets, time – frequency representations, continues time wavelet,
Continues wavelet
transform
(CWT), Inverse CWT, Properties of CWT, Discrete wavelet transform, STFT,
Comparison
of
Fourier transform & wavelet transform ,Application of wavelets transforms .
UNIT-VI: Application of Digital
Signal Processing (5 Hrs.)
Voice
processing – Analysis of speech signal, Speech analysis synthesis system,
compression and
coding
channel vocoder, Sub band and coding
Image
processing, Biomedical signal processing – ECG.
Text Books:
1.
John G Prokis, Manolakis, “Digital Signal Processing – Principles, Algorithms
and Application”, 4th
Edition,
Pearson Education Publication.
2.
Salivahanam, A Vallavaraj, C. Guanapriya, “Digital Signal Processing”, 1st Edition, Tata McGraw
Hill.
Reference Books:
1. P.Ramesh Babu, “Digital Signal Processing”, 4th Edition, Scitech Publication.
2
.Sanjeet Mitra, “Digital Signal Processing”, McGraw Hill Publication.
3.
Vinay Ingle, John G Prokis, ,“Digital Signal Processing-A MATLAB Based
Approach”,India
Edition,Cengage
Learning.
4.
E.C.Ifeachor Barrie,W.Jervis,“Digital Signal Processing”
5.
Ashok Ambardar, “Digital Signal Processing” India Edition,Cengage Learning.
6.
S.D.Apte India,“Digital Signal Processing” Wiley India.
7.
Robert J. Schilling, Sandra L. Harris, “Fundamentals of Digital Signal Processing
using
MATLAB”,
1st Edition,
Cengage Learning.
List of Experiments:
Minimum
10 Experiments Based on the above Syllabus.
Experiments
may be performs using Matlab/DSP simulator.
1.
Generation of DT signals
2.
Convolution and correlation of signals
3.
Computation of DFT & IDFT using standard formula
4.
Computation of DFT using FFT algorithms
5.
Computation of circular convolution
6.
Design of FIR LPF,HPF,BPF,BRF filter using Fourier series method
7.
Design of FIR LPF,HPF,BPF,BRF filter using frequency sampling method
8.
Design of FIR filter using Kaiser window
9.
Design of IIR LPF,HPF,BPF,BRF filter using impulse invariance method
10.
Design of FIR LPF,HPF,BPF,BRF filter using bilinear transformation method
11.
Design IIR filter using placement of poles & zeros.
12.
Computation of DCT
13.
Computation of wavelet transform
Guidelines for Paper Setter:
Theory
Question Paper should include 40 to 50% Numerical Problems.
T.E. (Electronics
Engineering)
Semester -VI
INDUSTRIAL MANAGEMENT &
OPERATION RESEARCH
Teaching Scheme Examination Scheme
Lectures
: 3 Hours/Week Theory : 100 Marks
Tutorial : 1 Hour/Week Term work : 25 Marks
SECTION – I
UNIT-I: Function of Management (6
Hrs.)
1)
Planning – Nature, Types, Improvement, Forecasting methods and importance
2)
Organization –Importance and Principles,
3)
Staffing –Procedure of staffing, performance, appraisal methods.
4)
Directing – Leadership styles
5)
Motivation – Theeries-Maslow’s, Herzberg’s, Mc Greqor’s.
6)
Communication – Process types, Barriers and Remedies.
7)
Controlling- process.
UNIT-II: Marketing (6 Hrs.)
Marketing
and selling concept, marketing mix, Advertising- needs ,types, advantages and
limitations.
Material
Management - Purchase and its importance, policies and procedure, Five R’s of
purchasing. Inventory Control - Inventory costs, EOG analysis, ABC analysis.
UNIT-III: Costing (6 Hrs.)
Elements
of cost, cost estimation procedure
Entrepreneurship-
importance, Qualities, function of entrepreneur, small scale industries –
procedure
of
starting SSI unit, Difference Schemes for SSI.
Forms
of Business Organization – Single, partnership, Joint stock, co-operative and
state and central Govt. Social responsibilities and business ethics-
introduction.
SECTION – II
UNIT –IV: (6 Hrs.)
Operations
Research –Definition, methodology, Scope and limitations.
Linear
programming – Concept, Formulation of LPP, Graphical method, Simplex Method.
UNIT- V: (6 Hrs.)
Assignment
Problems – Introduction Balanced, Unbalanced, Prohibitive type of assignments,
Hungarian
methods. Transportation Problems – For finding basic feasible solution by
Northwest corner method, Least cost method and Voget’s Approximation method.
UNIT- VI: (6 Hrs.)
Project
Management – Programmed Evaluation and review technique, CPERTI, critical path
method (CPM), Network Analysis, Identifying critical path, Probability of
completing the project within the given time.
TERM WORK:-
1)
Case studies on unit no- 1
2)
Numerical on EOQ, ABC analysis.
3)
Project proposal for SSI.
4)
Numerical on Unit no. 4
5)
Numerical on Unit no. 5
6)
Numerical on Unit no. 6
[NOTE: Any One numerical of above assignment must be solved using
Computer.]
Reference Books:-
Industrial management
1)
C.S. George, “Management for Businesses and Industry”,
2)
Bethel Atwater, Smithy, Stackman and Riggs, “Industrial Organization”,
3)
Koontz , Odonell, “Essential of Management”
4)
Stoner, “Management”,
5)
O.P. Khanna, “Industrial Organization and Management”,
6)
Telsan, “Industrial and Business Management”,
7)
Tripathy and Reddy, “Principles of Management”,
8)
Industrial Management – Tata McGraw Hill
Operation Research
1)
L.C.Jhamb sharma and Banga, “Qualitative Techniques – Vol. I & II”,
2)
W.L. Winston, “Operation Research”, Cengage Learning.
3)
Hira and Gupta, “Problems in Operation Research”,
4)
H.A. Taha and A.M. Nafarajuan, “Operation Research”, Pearson Education.
5)
A. Ravindra and D.T. Phillipos, “Operation Research”, Wiley India
6)
Gillet, “Introduction to Operation Research”, Tata Mc Graw Hill.
7)
N.D. Vara, “Quantitative Analysis”, Tata Mc Graw Hill.
8)
L.S. Srinath, “PERT and CPM (principles and Application )”,
9)
Ac Koff Sasieni, “Fundamentals of Operation Research”,
T.E. (Electronics
Engineering)
Semester -VI
Mini project
Teaching Scheme Examination Scheme
Practical
: 2 Hours/Week Term work : 25 Marks
OE : 50 Marks
Mini
project work should consist of following steps.
1.
Project Idea : Students should propose project ideas & finalize the project
idea in consultation
with
guide.
2.
Students should submit implementation plan in the form of PERT/CPM chart. Which
will
cover
weekly activity of project report.
3.
Problem definition and specification development in the form of synopsis.
4.
Design of circuit with calculation & should include
a)
Analog part b) digital part c) Power supply d) Test strategy
if
firmware is required produce flow chart.
5.
Simulation of design using tools like OrCAD, Matlab, etc.
6.
Design of enclosure & PCB.
7.
Fabrication & assembly of PCB & enclosure.
8.
Testing & calibration.
9.
Measurement of specifications.
Note:-
1.
Project report should include report of all above steps and conclusion.
2.
Project group should demonstrate and deliver seminar on project.
3.
A mini project should not exceed three students per group.
Guidelines for selection of
project ideas:-
1.
Battery charger: Voltage & current indication
Specification
like
a)
Over voltage protection b)Charging current rating
c)
Accuracy d) With all annunciations
2. Capacitance meter:
Specifications
a) Ranges b) Resolution c) Accuracy
3. Temperature indicator / ON-OFF
controller:
Specifications
a) Sensor selection b) Range c) Resolution d) Accuracy
4. Angular displacement
measurement using rotary encoder:
Specifications
a) Range b) Resolution c) Accuracy
5. Resistance meter (milliohms):
Specifications
a) Range b) Resolution c) Accuracy
6. DC motor speed controller using
power devices with indicator:
Specifications
a) Range b) Resolution c) Accuracy
7. FSM based digital design
Development
of timing diagram & Design of FSM using MSI, LSI PLDs ROM for
application
like sequence detector, sequence generator, counters, glass scale, industrial
timers
a)
Sequence generator: A typical PN sequence generator, Six stage MLS counters
using
shift
register (maximum length sequencer),Gray code generator
b)
Sequence detectors:, A combinational lock, Flag detection in synchronous
communications,
ASM based digital design:
ASM
technique- vending Machine, Lift controller, traffic controller, Washing
machine &
Micro
oven, Automatic bottle filling plant.
8. Micro controller Based Data
Acquisition System:
Temperature
measurement systems, Flow measurement system, Level Measurement System,
Design
a Microcontroller based weigh scale using load cell, Design an alarm
annunciator for
pressure
measurement system, Design an ECG amplifier with 1 mV calibration facility.
References:
Students
are advised to refer Application Notes, research publications & data sheet
of
various
electronics devices. from Motorola, National Semiconductors, Analog devices,
Texas
instruments, Fairchild, Cypress Semiconductors, Microchips, International
Rectifiers,
ST Microelectronics, Maxim, Philips, NXP, IEEE.
T.E. (Electronics
Engineering)
Semester –V
COMPUTER ORGANIZATION AND PROCESSOR
DESIGN
Teaching Scheme Examination Scheme
Lectures
: 3 Hours/Week Theory : 100 Marks
Tutorial : 1 Hours/Week Term work : 25 Marks
SECTION – I
UNIT-I: Evolution of Electronic
Computers (2 Hrs.)
Introduction
and History,IAS Computer architecture,IBM 360 model,stack passed computer and
polish
notation
UNIT-II: Design Methodology (7
Hrs.)
Design
levels: Gate level and register level, processor level, programmable logic
devices, performance measurement, state machine design, Melay machine, Moore
machine
UNIT-III: Processor Basic (6 Hrs.)
CPU
organization fundamental, Data representation, Basic formats, Floating point
numbers,
Instruction
sets: Instruction formats, Instruction type, Programming consideration,
Introduction to
RISC
and CISC.
UNIT-IV: Arithmetic Unit Design.
(8 Hrs.)
Fixed
point arithmetic: Byte and word , Adders, Subtracters, Multipliers: Booth’s
algorithm,
Robertson’s
algorithms, combinational array multiplier. 32/64 bit floating point
arithmetic:
(IEEE
754 format), introduction to pipeline processing.
SECTION – II
UNIT-V: Control Design (10 Hrs.)
Introduction,
Hard wired control, Micro programmed control, GCD processor Design, Design of
Control
unit for accumulator based CPU, DMA controller, control unit design, Micro
Instruction
format,
Interrupt and Branch, Micro Instruction processing, Instruction sequencing and
Interruption.
UNIT-VI: Memory Organizanition (7
Hrs.)
Memory
Systems, Multilevel memories, Address Translation, Memory allocation schemes
FIFO,
LRU,
OPT, etc. Virtual Memory, Cache memory.
UNIT-VII: Memory Organizanition (4
Hrs)
Processor
programmed I/O architecture, DMA architecture, Interrupt I/O hardware,
Text Books:
1.
J.P. Hayes “Computer Architecture and Organization” McGraw Hill publication.
Reference Books:
1.
Hamacher Zaki “Computer Organization” McGraw Hill publication
T.E. (Electronics
Engineering)
Semester -VI
ANALOG AND DIGITAL COMMUNICATION
Teaching Scheme Examination Scheme
Theory
: 4 Hours/Week Theory : 100 Marks
Practical : 2 Hours/Week Term work : 25 Marks
SECTION – I
Unit – I:Pulse Analog Modulation
(7 Hrs.)
Pulse
Amplitude Modulation (PAM),Sampling Theorem and Type : Natural and Flat top,PAM
modulator
Circuit,Pam Demodulator Circuit,TDM and FDM,Pulse Time Modulation,Generation of
PTM signals(direct and Indirect), PWM modulator,PPM modulator and PPM Modulator
and
Demodulator.
Unit – II: Random Variables &
Processes (6 Hrs.)
Random
Variables: Cumulative Distribution Function(CDF), Probability Density
Function(PDF),
Joint
CDF & joint PDF, uniform distribution, Rayleigh distribution & Gaussian
PDF.
Random
Process: Mathematical definition of random process, Stationary process, Ergodic
process, Power spectral density of stationary random process. Noise in
communication system, white noise, Thermal noise, Noise equivalent Bandwidth,
Noise Figure.
UNIT-II:Pulse Digital Modulation
(9 Hrs.)
Pulse
Code Modulation (PCM): PCM generation and reconstruction,Quantization- Uniform
Quantization,
Non uniform Quantization, Companding, , Effect of noise, Bandwidth,
Differential
Pulse
code modulation (DPCM), Delta modulation, Noise in delta modulation, Adaptive
delta
modulation(ADM),
CVSD. Performance of all coding schemes based on SNR.
SECTION – II
Unit-IV: Digital Signaling Formats
and Base Band Transmission (6 Hrs.)
Introduction,
Data format: Non Return to zero(NRZ) codes, Return to Zero, Bipolar,Manchester,
Phase
Encoding, Synchronization- Bit or Symbol Synchronization, Frame
Synchronization, Carrier recovery circuits, scramblers & unscramblers,
Inter symbol Interference (ISI) & its minimization, Eye Pattern
SECTION – II
UNIT –V: Digital Modulation
Techniques (10 Hrs.)
Amplitude
Shift Keying (ASK), Phase Shift Keying (PSK), Frequency Shift Keying (FSK),
Coherent & Non-coherent detection, Binary Phase Shift Keying (BPSK),
Quadrature Phase Shift Keying (QPSK) , Differential Phase Shift Keying (DPSK),
Differentially Encoded Phase Shift Keying (DEPSK), Minimum Shift Keying (MSK),
Gaussian Minimum Shift Keying (GMSK), Quadrature Amplitude Modulator (QAM).
Bandwidth, Signal Space representation, Probability of bit error of all Schemes.
UNIT – VI: SPREAD SPECTRUM
MODULATION (6 Hrs.)
Introduction,
Direct Sequence (DS) Spread Spectrum, Use of Spread Spectrum with Code Division
Multiple
Access(CDMA), Ranging Using DS Spread Spectrum, Frequency Hopping (FH) Spread
Spectrum,
Generation & Characteristics of PN Sequences
Text Books:
1)
Simon Haykin “Digital Communication” Wiley India Edition
2)
Taub & Schiling “Principles of communication System”IInd Edition, Tata
McGRAW Hill
3)
Bernard Sklar “Digital Communication-Fundamentals and Applications” IInd
Edition ,
Pearson
Education
Reference Books:
1)
B.P. Lathi “Modern Digital & Analog Communication System”
2)
Singh & Sapre “Communication Systems”
3)
Glover & Grant “Digital Communication” IInd Edition, Pearson Education
4)
John Prokis ”Digital Communication” Pearson Education.
5)
K.Sam Shanmugan “Digital & Analog Communication Systems” Wiley India
Edition
6)
M.S. Roden “Analog & Digital Communication Systems”, 5th Edition, Shroff Publications.
7)
Das, Mullick,Chatterjee “ Principles of Digital Communication” New Age
International.
T.E. (Electronics
Engineering)
Semester -VI
ELECTRONIC DESIGN TECHNOLOGY
Teaching Scheme Examination Scheme
Theory
: 4 Hours/Week Theory : 100 Marks
Practical : 2 Hours/Week Term work : 25 Marks
SECTION – I
Unit – I: Switch Mode Power Supplies (SMPS) (7 Hrs.)
frequency
ferrite core transformer design, Selection of ferrite core. Selection of major
SMPS topologies (Step up, Step down, Push pull, Negative converter), SPMS
controller ICs: 3524 TL 494, Design of SMPS for industrial application: Battery
chargers, Computer power supply, MOPS with current limit protection. The design
should include high components e.g. Power transistor filter capacitor,
rectifiers.
Unit – II: Signal Conditioners (8
Hrs.)
Temperature
– RTD, Thermocouple, Semiconductor LM 35, AD549, Strain gauge type transducers of
350 ohm/120 ohm bridge configuration, Variable capacitor transducer signal
conditioning using Voltage to Timeand Voltage to Frequency conversion., V to I
and I to V converters for standard input and output,Standard input output
ranges – 0 to 2V (DVM), 0 to 5 V(Micro controller),
4
to 20 mA (Industrial)
UNIT-III: Analog process controllers (9
Hrs.)
Analog
process controllers using above transducers: ON/OFF, proportional, PID
controller
Algorithm
implementation only for any 8-bit Microprocessor/ Micro controller
based
process controllers. (No up H/W to be designed).
SECTION – II
Unit-IV: Discrete I.C design (6
Hrs.)
Discrete I.C design of 3, 3½, 3 ¼ digits – DVM
design with reference voltage
of
1,2, 4 volts. Attenuator circuit design for voltage current dc only .)
UNIT –V: Control circuit design (6
Hrs.)
Control
circuit design for frequency time measurement. Design of clock
divider,
Reset, Load pulses. Output requirement of latch and counters depending
upon
resolution
UNIT – VI: Industrial TIMERS and counters (6 Hrs.)
Fundamentals
of IC timers, CMOS timer & 2240 Binary Programmable
Timer/counter,
use of timers for event or interval timing ,Design of counter using IC 7226
& 74C926 for the event counting, frequency and period measurement
UNIT – VII: Design of frequency synthesizer (6 Hrs.)
31
Shivaji
University, Kolhapur
Design
of frequency synthesizer using 4046 and 565, EPROM based synthesizer,
line
frequency monitor using PLL 565 with resolution of 0.01 Hz.
Reference Books:
1.
National Semiconductor Manual
2.
Linear IC Manual
3.
AK Ghosh, “ Introduction to instrumentation control”. Prentice Hall India.
4.
A J Bouwens, “Digital Instrumentation” McGraw Hill.
5.
W Bolton, “Industrial Control and Instrumentation” Oriental Logman.
6.
J.Michael Jacob, “Industrial Control Electronics- Applications and Design”
Prentice Hall of
International
Inc.
7.
George Chrysies, “ High-Frequency switching power supplies- Theory and Design”
McGraw Hill.
Shivaji
University, Kolhapur
Equivalences
of T.E. Electronics for repeater students
(Semester-V)
Sr.No T.E Part-I (Pre- Revised)
Equivalent Subject/ Replacement Subject
1
Control Systems Control System Engineering (Revised)
2
Microprocessor-I Microprocessor Peripherals & Interfacing
(Revised)
3
Electro Magnetic Engineering Electro Magnetic Engineering (Revised)
4
Computer Organization Computer Organization and Processor Design)
(Replacement
5
Communication Engineering-II Analog and Digital Communication
(Replacement)
6
Mini Project Mini Project
(Semester-VI)
Sr.No T.E Part-II (Pre- Revised)
T.E Part-II (Revised)
1
VLSI Design Digital System Design
2
Industrial Electronics Power Electronics
3
Electronics System Design Electronic Design Technology (Replacement)
4
Microprocessor-II Microcontrollers
5
Industrial Management &
Operation
Research
Industrial
Management & Operation Research
